How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have a distinct set of steps to add the second key. It requires dealer service using an electronic handheld computer called Tech-2. Then the transponder must be replaced and a key must be purchased.

Rotate your keys to prevent one from wearing out faster than the other. This will also keep your keys in pristine condition.

Replacement Case

Unlike the classic saab 9-3 key replacement keys of old keys, the new keys have electronic components which makes it difficult to copy. That has made car theft a lot more difficult than it was twenty years ago. It also makes it more expensive to replace keys lost.

Saab 9-3 owners must have two keys that work. It is costly to replace a lost or damaged key since it requires replacing the CIM module, and changing the locking cylinders. Dealers charge between $100-$200 to do this.

There are ways to avoid these costs. Some parts suppliers can look up the code on an extra key (usually the same one that opens the doors and turns on the ignition) and cut a brand new metal key blade for less than the dealer's cost. The key, however, must be identical to the original one in order to function within your car.

Follow these steps to replace the case. You'll need a flathead screwdriver along with some patience. With the screwdriver, pry away the plastic and take out the emergency key. Once the case is open, remove the electronic components and place them into the new case. Place the key with the correct badge inside the case.

Replacement Battery

The Saab 9-3 replacement battery is a cheap part that can be easily and quickly replaced. This YouTube tutorial for DIY Cyclone Cyd shows how to replace the battery for the remote key fob in only four steps. This tutorial is suitable for any modern saab key fob though the process may vary slightly.

The button is normally located next to the Saab logo on the back of the fob. This is usually located near the Saab logo on the back of the fob. Next take a flathead screwdriver to insert into the tiny hole in this button. This should be enough to open the case of the fob to allow you to replace the battery.

Once you have installed the new batteries CR1632, it is possible to put back together the remote key fob. You can then program it into your car. The entire process shouldn't be more than an hour. It is a very simple process that does not require any special equipment.

The process can be a bit more complex if you lose your key, but still possible. The dealer will first need to read the VIN of the vehicle and order an alternative TWICE module, as well as a key blade that has the correct unique code. After that, they will be required to cut the replacement key and then program it using a brand new tool for programming called MDI.

Replacement Key Fob

The key fob comes with batteries that are used to lock and unlock your car. The batteries have a lifespan and will eventually die. This is a problem that occurs in all vehicles. The good news is that you can change the batteries in most key fobs without having to replace the entire case. You can buy replacement fobs from Amazon that have all the electronics already installed, so you can simply open the case and replace those batteries that are old. It is important to remember that you'll have to remove the emergency key first. you can do this by inserting the screwdriver of a small flathead into the slot that is located in the middle of the case. The case will split when you rotate the screwdriver around it.

If you're planning to replace your keys, keep a spare in your possession. This will save you a lot of money. If you have a spare, you can ask the dealer to cut an entirely new key and then program it into your car, which is cheaper than replacing the entire key fob.

It is possible to add a second key to your car If you don't already have one, however it requires an extensive amount of research and effort. It costs a few hundred bucks to add an additional car key. The computer of the vehicle must also be programmed. Professionals can accomplish this but it's not a cheap option.

Replacement Ignition

In contrast to the earlier saab 9-5 key replacement (our source) automobiles, the new saab 9-3 replacement key 9-3 models feature an advanced alarm system that is dependent on a coded keys. This means that should you lose only one working key, replacing it with another one can be very expensive as the car has to have a unique computer module fitted and also needs to be specifically programmed to accept an extra key. Most locksmiths cannot do this and even dealers will charge hundred dollars just to program the new key!

Dealers will charge you top dollar to replace your car computer (also known as the CIM or SAAB twice) if you lose your only working key. We can reprogram the EEPROM in your car computer so that it's ready for an extra key. This will save you more than 50% on the cost you spend at an auto dealer.

If you've been a long time owner of an 03-11 saab 93 replacement key 9-3, you likely know that the ignition key isn't very robust. If your ignition key is not functioning properly, you must consider replacing it. They can become sticky and the buttons are known to fall off. Fortunately, replacing the ignition key isn't as complicated as it sounds and can be done quickly with the appropriate tools.