How to Replace a Kia Sportage Replacement Key

For a variety of 2014 kia sportage key Fob - https://kingranks.com, models keys, the key has an integrated keyless entry system. The key can be compared to a remote control and can be changed with a brand new one from an kia cerato key replacement dealer or a locksmith.

Key fobs are prone to malfunction for a variety of reasons, such as batteries that are dead worn buttons signal interference, water damage and a malfunctioning receiver module. Here are some guidelines on how to get your Kia Sportage replacement key for kia soul 2011 key working again.

How do you replace the remote key or smartkey?

It doesn't matter if your Kia is equipped with an intelligent key, remote key push to start key, or a regular non-transponder steel key, the battery in these keys will eventually require replacement. This is especially relevant if your car displays a message that the smart key or remote has low battery power.

This is a relatively easy process. In order to replace the battery in the key fob, remove the mechanical key from the hole in the back of the key fob. Then pry open the cover. A small screw is inside the key fob to hold the battery in place. Using a small screwdriver, loosen the screw and pull out the old battery. Then insert the new one and close the slit in the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're all set! You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to do some errands in Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a programming machine, which is only available to the locksmith for cars or dealer. Other keys (non transponder keys made of steel) are not required for programming. If your key needs to be programmed again, you must be aware of the key code number written on the tag that identifies the key and save the number in a secure place.

How do I replace the battery?

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is most likely that the battery is depleted. A weak battery could cause other issues, such as the check engine light turning on or the engine not running correctly. It is quite simple to replace the key fob batteries by using only two tools.

Make sure that you shut off your vehicle and close all doors prior to beginning. Find the small, metal or plastic piece on the bottom of your key fob and move it until a metal key slides out. Then, you can insert the key into the handle on the door of your driver to open your car.

To replace the battery on the key fob, you must remove the cover at the rear. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then orient the new one in a way that the "+" positive side faces you and the "-" negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or breaking the contacts on the metal.

Once the new battery is installed, turn the key fob off and back on in the ignition several times until the door locks cycle. You can then test the Kia's Key fob again to make sure it's functioning properly.

How can you replace the smart key?

Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The smart key has an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs have batteries that eventually require replacing. This is an easy process that takes just two minutes.

Make sure you turn off your Kia, and be on a level or well-lit surface prior to when you begin. Be aware that there are small parts inside the fob that can fall out if you are not vigilant.

The first step is to locate the small release button on the back of the lower part of the fob. It's either an oval or circular slot. You can open the key fob by pressing the button.

After the key fob has been removed, you can remove the old battery. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After you've finished, your key fob should allow you to lock, unlock, and start your vehicle even if it's not running.

How do you replace the mechanical key?

The Kia key fob is a wonderful feature that lets us lock and unlock our car with the touch of one button. Like all devices it is possible that the 2013 kia rio key fob programming key fob can occasionally have problems. There are steps to take to resolve these issues and ensure that our key fobs are in good working condition over the long haul.

One of the most frequent problems is a weak or dead battery. This can cause your fob to stop working or work intermittently. If this is the problem it is time to replace the battery an entirely new battery.

If this doesn't solve the problem, try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to harm any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a new one.

Once the new battery is installed, close and unlock the doors using the mechanical key (every kia fob has an emergency mechanical key that will fit into the slot). Test the key fob and ensure that it's working properly. Contact a dealer or a locksmith to address the issue in the event that the fob is not working. To avoid a lockout in the future ensure you purchase an emergency key that will work on all door and trunk cylinders.