Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they do not corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will save you from costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it can cause a great deal of damage to your home, making it very dangerous and potentially fatal. It is crucial to take the time to ensure that you're doing all you can to ensure that your windows are in good shape.

Single-pane windows are relatively simple to replace and typically fit into frames of the past easily. If you have double-paned windows which are joined by internal beading, it is harder to remove and replace the old panes. In this instance it is essential to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you're planning to try to remove the window panes yourself it is crucial to wear the proper safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a dropcloth before you begin working on the glass so that any shards will fall onto the cloth instead of landing on the floor where they can be trampled on and cause further damage.

After the glass has been removed from the window, it's best to seal the gap with clear packaging tape or duct tape to block drafts and water from entering the home until a professional can come out and fix the window. It also acts as a barrier that will prevent any intruders from getting access into your home. If the distance between the window and the door is significant, you may want to use an alarm system that includes a window. This will give you the best of both.

2. Sagging

Upvc windows and doors are a low-cost, durable and energy-efficient alternative to timber sash windows. Over time, they can develop a number of problems, including sliding. A sagging uPVC window can cause issues with light, draughts, and even security. It's crucial to act as soon as you discover that your uPVC windows are sliding.

Repositioning the hinges could help fix a window repairs near me that is sliding. You'll first need to open the windows to get at the frame. Then, remove both the hinges at the top and bottom with a screwdriver and adjust them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and check for an appropriate fit. If you're happy with the fit, you can tighten the screws until they remain in the right place.

If you can't reposition the hinges, you might require replacing the seal. Rubber seals can dry out and lose their elasticity over time, causing them to loose their elasticity. It is crucial to replace your seal as quickly as you can in order to keep your uPVC window waterproof and draughtproof.

uPVC handles can also loosen up. This is typically caused by screws that have loosened over time, but it could be caused by the handle mechanism wears out. Fortunately, it's easy to fix the loose uPVC window handle yourself. The first step is to close your window and do an initial test fit. The corner joints of the sash must align with the casing joint. If it doesn't then you can use the screwdriver to loosen the handle. Then, you can turn the mechanism into position.

3. Water Leaks

It is important to take action if you awake each day to find mouldy walls and floors that are wet. Water leaks from windows can not only cause degrading of the structure of your home but also undermine your efforts to regulate the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is a fairly simple fix that can be completed by any competent DIYer. Depending on how severe the issue is, old caulking might need to be removed. It is essential to keep in mind that when it is about upvc window repairs near me window repairs, you should not be tempted to apply too much caulk' as this will only make the area more difficult to clean and decrease the efficiency of your energy usage.

Make sure that the drainage holes do not have debris inside them and that the sill pan has been properly angled to allow the water to drain from the window. In more serious cases, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. This is a fungus that thrives in damp conditions and is able to quickly spread throughout the home.

It is also important to remember that if the leak originates from the glass of your double-glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sliding. A uPVC specialist can easily solve this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open, or if it opens in a breeze. Anyone who is a skilled DIYer can fix these in a matter of minutes.

Like any mechanical component hinges are prone to be damaged over time. It's very simple to change a window hinge, but it's easier if someone else helps you to hold the frame.

Verify that the uPVC hinges are open and closed in the correct direction. You can do this by checking for the arrows on each hinge, this shows which way the window repair should be opened.

The problem with the hinges on windows could be caused by improperly opening the window a certain manner or because of inadequate installation at the factory. Sending us a picture via our website is often enough to solve the issue. We are always happy to give assistance.

It is also crucial to grease the hinges on a regular basis. Applying an engineering lubricant that is light to the hinges is a good way to do this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more easily. It can also prevent corrosion and decrease the chance of sticking. The ideal time to perform this every year. WD40 and other solvent-based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a variety of different things. First, the hinges due to wear and tear could become misaligned. This can cause an opening to appear where the sash joins the frame. They can be repaired by giving them thorough clean, however when they're beyond repair, it might be necessary to have them realigned or replaced. The interlock, which is located on the hinge of the window, can also become misaligned, again it's possible to just give them a good clean, but in certain cases, it may be necessary to get them replaced.

These seals are susceptible to wear and tear or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass, this will help to regulate indoor temperatures and again will lessen the risk of draughts.

Another, and most effective ways to cut down on the draughts in your home is to use an draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be put on top of your windowsill. These will keep your home warm by blocking cold air.

With a little maintenance and repair your windows made of upvc will continue to provide a great level of security and insulation for your home. It is crucial to realize that all windows have a lifespan and they may reach the point when it's more economical to replace them than fix them. So, if you are experiencing issues with your Upvc windows, it is always best to seek professional assistance immediately.