How to Repair a Bifold Door Top Pivot

A bifold closet door's top pivot could be loosened and scrape the floor. You can correct this by loosening the set screw for the top bracket slightly.

The top pivot pin is a screw made of metal that is inserted into a plastic cap with an end that is lipped and stays within the track, above the door. You'll also require an screwdriver and perhaps a pair pliers.

Take off the pin at the bottom.

Bifold doors are great to save space in a closet however, they can begin to sag or scrape against the floor, or even pop out of their brackets. The good thing is that you can repair bifold door top pivot the problem by making a few simple adjustments.

The most frequent issue is the bottom pin that becomes loose or slips out of its bracket. You can correct this by depressing the spring-loaded wheel at the top of the door and swinging the door into position to align it with the bottom track. When the gap is even you can tighten the screw that secures the top pivot point bracket to hold the door in position.

Another common issue is when the door's bottom is pushed into the carpet and scrapes along it. This can be caused by the addition of carpet or the flooring material. It could also be the result of an uneven gap between the door and hinge-side jamb. This can be fixed by loosening the top guide and sliding it inwards or removing the pivot point at the top and shift it out or in.

The final issue that is common is when the track isn't aligned. This can be fixed by loosening and moving the screw on top of the set screw in or out, as needed. After you've adjusted the nuts and bolts holding the track in place, you should be in a position to slide it back into its track bracket and secure it using the screw.

To remove the bottom pin from the bracket, lift the panels slightly, then secure them in place. Release the locking levers on the bracket's bottom to let the pin go. If the pin doesn't have a bracket for mounting, you can attach a screw with a flat head between the bottom of the pivot flange and the door to pull the pin from the door. Once you have an ensconced grip on the pin turn it left and right, while pulling it out of the door. If you aren't able to remove the pin, you might have to take the entire panel from the track system. If this is the situation, you can put it on saw horses to make the process easier.

Remove the pin with the highest point.

They are great at saving space but can be frustrating if they start to sag or scratch the floor or jump off track. A few minor adjustments can often get them back in line.

If the doors are sliding unevenly you can loosen the screw on the top pivot point bracket using an screwdriver and move it just a bit. Close the door to determine if it aligns well with the frame. If it does, tighten up the screw.

The bottoms of bifold door repair internal doors often scrape the carpet. If this is the case, you can try raising the bottom of the door using the bottom pin adjustment. But if the door is too high, you'll have to take it off and trim them with a saw.

As time passes over time, the wood around the pivot and anchor pins can crack. It is possible to use epoxy to fix the crack and stop it from getting any worse. Apply a small amount of the epoxy to the crack, and allow it to dry before opening the bi fold door repairs.

It could be that your bifold doors are too spaced apart. You can fix this by moving the top of the door either up or down on the track.

It's not easy to tackle this project on your own, so you'll need an assistant. Start by grabbing the outer and inner doors at the sides, then raise them up. They can be stacked to make it easier to handle.

If there are locking levers on the pivot bracket, release them. Otherwise, grab the top of the pin using a pair of vise grips, and twist it from left to right, while pulling it out. Repeat the same procedure on the opposite side of the door. Once both pins have been removed, the bi folding door repair will open and align with the track. If this doesn't work it's possible to try again. You can use a drill to straighten out the track if it is bent.

Reinstall the pin on the bottom.

If the bottom pin does not work properly, it can cause the door to be bowed and stop it from opening or closing easily. Fortunately, the issue is usually easy to fix. Most of the time the issue is a missing or loose mounting screw is at fault. If this is the case, it's best to replace the screw with a new one that is the same size. Screw it into the correct position and tighten it.

If you're serious about your bifold repair project, use an air pressure gauge to check the top pin that is spring loaded for proper compression. The gauge is also helpful in determining if the pin itself is damaged or cracked it is an important piece of information to have if you're planning on replacing it with a new part.

Measurement of the diameter of the pin cap and the diameter of the pivot pin will help you determine if the pin is damaged or worn out. Compare the measurements with what is available online for replacements. This will help you to find the right parts for your door.

Before you install the replacement pivot pin to the doors, open them and lean them against each to ensure that they're in the proper position to be installed. If you're using a set of knobs for closet doors, carefully mark a level line down the center of the leading edge of each door. You can use a long-length level to ensure that the top bifold track aligns with the jambs and is level.

Once the doors have been installed, insert the top pin into the pivot guide of the track. Then, you can swivel the bottom of the door until the pin rests in the bracket that is shaped like an L. If the door doesn't fit between the top bracket and the bottom guide you can raise or lower it by removing the pivot that is adjustable at the bottom of the doors. Verify that the gap between the door and the hinge side jamb is equal by using a long-length level and marking a plumb line down the middle of the door frame.

Reinstall the pin with the top

A bifold is a set of hinged panels that are folded back on tracks and placed on the opposite side of the door opening. They come in different styles like solid or paneled and louvered. They can be utilized in closets, laundry rooms, hallways or even bedrooms. If you already have a pair of bifold doors which scrape the floor or aren't working properly, it's possible to adjust them by adjusting the top and bottom pivots.

Remove the top pin first from the upper track. Then, slide the bottom pin into the bracket, and then check if there's an even and correct gap between the jamb side of the frame and the door.

If the gap is too large it is possible to raise the bottom of the door by loosing and fixing the pivot adjustable on the bottom of the door. This will push the door's bottom towards the frame and narrow the gap. You can also adjust the height of the track hanger by loosening the screw on the repairing bottom of bifold door and then adjusting it with a wrench to reach the desired level.

Install the top track bracket on the hinge end of the door frame once you have installed the track hanger. Follow the instructions and diagrams that came with the kit to ensure that it is placed precisely. Be sure that the track is flush and level with the floor prior to fixing it.

Take measurements of the width and height to ensure you have the correct track and hardware kit. If you're unsure of how to set up your bifold doors, consult with an expert installer to ensure that the installation is completed correctly. They will be able to tell you whether the bifold doors that you've chosen are the correct size for your space, and they can help you select the right design that is suitable for your home. If required, they will trim the doors so that they fit. This could save you time and money.